Jump to content
Sign in to follow this  
rontarrant

Mix Compensation for Hearing Impairment?

Recommended Posts

When mixing, how can I compensate for the fact that I'm partially deaf in one ear? From hearing tests, I know the approximate range and more or less how deaf I am in db.

Is there a way to turn this information into some kind of filter so that—using headphones—I can still get decent results? Or am I just at that point in life where I should forget about recording and just content myself with playing on the porch?

Share this post


Link to post
Share on other sites
Posted (edited)

I'm sure this is a common problem  with the aging boomer generation. I have severely compromised high-frequency hearing acquired in the military. Up until now my strategy has been to mix it as best as I can taking into account my hearing loss and then letting a lot of different people including people on this forum hear what I've done.

If I recall correctly sonarworks plugin has an algorithm that applies correction based on the average frequency degradation for a given age range, but I don't know if that will help you given the nature of your hearing loss.

I think what makes the most sense is knowing what frequencies are compromised and setting up a special EQ that compensates for them.  

However you choose to deal with it,  sitting on the porch hasn't been an option for me.

Edited by Kevin Walsh

Share this post


Link to post
Share on other sites

Thanks, Kevin. I found a discussion on another forum about this and most said that despite hearing loss, it didn't seem to affect their mixes. A few said they'd had others with confirmed good hearing listen only to find that the mixes were fine. I suppose the thing to do is carry on and play it by ear. :)

Share this post


Link to post
Share on other sites

Izotope tonal balance control can be helpful to get some feedback about how the frequencies of a song match with their preset references. Reference tracks might help just to check and stuff like eq matching to a mix you like.  Porches are fun recording is more fun 😀

  • Like 1

Share this post


Link to post
Share on other sites
On 5/24/2021 at 11:02 AM, treesha said:

Izotope tonal balance control can be helpful to get some feedback about how the frequencies of a song match with their preset references. Reference tracks might help just to check and stuff like eq matching to a mix you like.  Porches are fun recording is more fun 😀

Thanks, treesha, and I agree... about the porches. :)

  • Like 1

Share this post


Link to post
Share on other sites

I don't think anyone hears identically in both ears. I certainly don't. My left ear is more sensitive to upper mids and high frequencies. I blame it on many years standing stage left with bands blasting into my right ear. Now, when I talk on the phone it's always held to my left ear. To make sure that's not coloring my mixes, I'll flip my headphones around and see if I still like the mix. (I don't mix on headphones, but headphones in a dark room are always my final QA test.)

If the frequency response is similar in both ears, the easiest solution is in the pan control on the master bus (or headphone mix bus if you use one). That control is a simple balance control like the one on your hi-fi labeled "Balance". It just controls the relative left and right volumes.

But if your "bad" ear doesn't register high frequencies as well as the other one, an equalizer can be set up based on the results of your hearing test. Hopefully, the test resulted in a detailed frequency response graph. If not, get a better hearing test from an audiologist who does hearing aids. They have to know the frequency response when prescribing hearing aids, which have built-in filters just for such compensation. The results of such a test should allow you to use an EQ plugin the same way an audiologist adjusts those filters.

I'd suggest setting up a headphone mix bus if you don't already have one, and have an audio interface that features extra outputs or that can route specified inputs to the headphones. This is a bus that doesn't go out to the main speakers and isn't involved during exports - it's just for monitoring via headphones. Having a separate bus for your headphone mix not only means you can compensate for hearing imbalances, but also for the frequency imbalances that are built-in to the headphones themselves. Of course, you could also just insert the compensation on the master bus, but then you'd need to remember to bypass those plugins whenever you export.

  • Like 1

Share this post


Link to post
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
Sign in to follow this  

×
×
  • Create New...