Terry Kelley

I see what McLeod is suggesting but I think it would be easier to use automation to turn on and off the effect at the times you want. This assumes the effect plays nicely when you bypass or set the mix to 100% dry depending on the effect itself. So don't like being switched on and off and click or make a noise. Bounce to a clip when you are happy with it. What effect are you working with?

I see this too quite often. While the developers will need to chime in, I think it works as intended. I lose the clip if I click on a different clip or track (or some combination of that.) I suspect they feel they've lost track of what I am doing. As long as I stay on the same track I don't lose the clip. Not a technical explanation but I think the issue it somewhere around that.

Show off!

Oh, right. I see that now. I like that.

Which is ...

Ok

Agreed. There are various solutions but right now I can't always tell what the digits are. Maybe even a separate display up in the control panel. But make them easier to read.

The world makes sense again.

Move the aim assist digits in front of the assist line. Right now, you can't always ready the numbers.

Sonitus Delay in manual mode will do what you want. It will go down to .1ms and up to eternity.

I do the two step method. Assuming you want to keep the song in tune, I change the pitch first and then change the length. Each half step is the 12 root of 2 or 1.05946309436 so use that to calculate how much to speed it up or slow it down.

I've had unfreezing crash with the latest release. I only recently started using freeze more to remove CPU load and have noticed weird behavior. also, as I posted elsewhere, unfreezing doesn't always position the clip correctly.

I seriously doubt we can "rush" them. But what the hell, let's try it!

The futures so bright I need a metaphor.

Do a Shift J to clear the meter peaks. While that reverb has some great sounds, it's a DX plug-in and goes totally goofy at times. One thing I've learn is NEVER change a setting while it's playing. It will glitch and melt down. Sometimes you can get away with it. But - Just don't. I think this is what you are noticing. It won't get better. Just learn how to use it. I use it a lot.

I've noticed that sometimes when I unfreeze a clip, the unfrozen clip will be a few beats earlier than where it should be. And re-freezing it "appears" to place it where it should be. I say appears because I've only tried it a couple of time and more often than not unfreeze positions the clip correctly. But here and there, they are too early when un-frozen. It also appears to happen only to Melodyne edited clips but again, I need to check more closely when it happens. Anyone else experienced this?

Other things to do first?

I just figured someone might go "yep or nope." LOL. I didn't think we get into a deep alternative analysis. I fired up Reaper and tried various combinations of EVERYTHING and I think the noise is an artifact of the filtering itself. You don't notice it normally so I'm not going to dig any deeper.

Guitar Center shows it for $129. Didn't try ordering it. I'm trying to figure out what's happening with LP-64. Maybe I do need to dump it,

NM.

Ah, never played with that one.

Hi Bit, I tried all of the standard fixes and it doesn't work. It's sounds like something is being over driven. Promidi, Expert Settings?

Hopefully someone can check this - play something with a fair amount of low mid-range/upper bass and solo the lower mid-range band in LP-64. Do you hear noise like it's being over-driven or clipped? I was mastering a low volume section with a fair amount of lower mids and could hear some noise and start soloing tracks and it didn't change. Then I soloed each band in LP-64 and found it was in the lower mid band. To be sure, I switched interfaces, speakers and headphone and it was still there. I loaded several other projects and it was still there. I disabled all effects on all of the tracks and it was still there. It's something to do with LP-64. Disable LP-64 and it's gone. I switched to Sonitus Multiband and it's clean. Weird. Maybe it's something upstream I am missing? I reinstalled it from the old discs and it didn't change. I like LP-64 and hate to have to switch although there are plenty of alternatives.

Oh, I was thinking it would go look since there is a VST in the effects rack. But it sounds like the answer is "it doesn't" Thanks everyone for the info. I'll start bouncing to tracks more. I do it now for sub-mixes but never thought to use it for this.

Thanks. So what is the reason it doesn't?