scook

Then there are the presets using the Valleys simulator.

The Event Inspector module is in the Control Bar. Here is a video discussing Duration in the Event Inspector module

There are links in the main ProChannel help page for each plug-in's detailed help. As noted above, the DAW records the signal at the track input. Here is a signal flow diagram that may help. If you wish to record an incoming signal with the ProChannel or other effects applied, add a send to an aux track and record the aux track. This works because the aux track input is after the original tracks ProChannel and FX rack. My want to record the original track along with the aux track, just in case.

With the Smart Tool, right-click and drag to lasso notes. Enter 200% in the Event Inspector Duration entry to double note duration of selected notes.

When sharing with others, always use wav files. DAWs have to convert mp3s into wavs which may result in the timing not being exactly the same as your original project. This would not account for an offset of an entire measure though. Different sample rates would not either. Usually, broadcast waves end up far down the timeline, not just a measure off and not early. There are two ways to avoid sync issues, broadcast waves or always starting clips at 0.

Either run CbB as administrator or modify the registry. Users need full control over HKEY_LOCAL_MACHINE\Software\rgc:audio software\DXi\Pentagon I. Here is an image showing the process in regedit:

Not update related. Check the On Stop, Rewind to Now setting. Keyboard shortcut CTRL+W.

While the example above works for anything that can be grouped, if I needed shared/inverted volume automation, I would not mess with MIDI and CbB volume controls instead opting for free Blue Cat Gain plug-ins. In this video the Blue Cat Gain plug-ins are added to two tracks, then set to Group A (the plug-ins have their own built-in grouping) with one reversed (again built into the plug-in) and automated using one of the plug-ins gain settings.

Could group the controls to automate and use a MIDI track to host the actual automation (as MIDI data) using a virtual MIDI cable to drive one of the grouped controls via remote control Here is an example of two tracks with volume grouped, one of them is inverted and a MIDI track sending modwheel data via LoopBe1 to one of the controls in the group.

Sure, one could use the "all mono" option which results in 32 audio tracks, 16 BFD3 mono tracks and 16 left and right channels for the stereo tracks. Rather than mess with cleaning up the unwanted tracks, in this case, I was suggesting a different method as a learning exercise, one track at a time. Often, multi-out drum synths involve a combination of stereo and mono tracks. Both "all track output" options don't quite fit the bill.

yes, https://www.google.com/search?q=midi+expression+pedals

Your time may be better spent learning the plug-in. It is a large/complex plug-in with the ability to tailor each kit piece individually in the plug-in with the myriad of built-in effects and routing options to mix in the plug-in to a single stereo out. That said, if you really want to bypass BFD internal mixer, start simple. Do everything in little steps and you should be able to figure out how it works. Once you get the entire kit setup with MIDI and audio tracks, save it as a track template and use the template to load BFD in the future. Here are some little steps to get you started - In CbB, drag the BFD3 plug-in into a project with only MIDI source selected in the Insert Soft synth Options dialog. You can always create a folder and move the tracks into it later. In BFD3, load a kit In CbB add an audio track, change the label to Kick set the interleave* to mono set the input to BFD3m01 (Note: BFD3m... are BFD3 mono outputs, BFD3s... are stereo). In BFD3 change the Kick in the BFD3 mixer to Mono 1 test by clicking on the Kick in the BFD3 kit view In CbB add an audio track change the label to snare set the interleave* to mono set the input to BFD3m02 In BFD3 change the Smare in the BFD3 mixer to Mono 2 test by clicking on the Snare in the BFD3 kit view At this point, chances are the kick and snare will both play albeit at different levels on both tracks. This is because BFD3, by default allows the kick and snare to bleed into each other's microphones. This is controlled in BFD3 in the tech display to the right of the Kit and Mixer display. Repeat as desired for each kit piece. * Track interleave is located in the track inspector and depending on Workspace and Track Control drop down settings in the track view track headers.

It is possible to add tracks for any synth including Session Drummer 3 at any time. Additional MIDI track need their output set to the synth. Additional audio tracks need their input set to the synth. If you are using instrument tracks, there is a function to append instrument tracks to a synth with multiple outputs. Right-click one of the instrument track headers in the track view to access this option.

mix recall may help

Yes, buses are audio only so their FX racks and Prochannels work too. Typically, a soundfont player is a plug-in loaded into the DAW like any other soft synth plug-in. All soft synth plug-ins require an audio or instrument track to work in the DAW. Maybe you are using an external synth like VirtualMIDISynth. If so, you may want to reconsider. Using external synths like the MS GS Wavetable synth, VirtualMIDISynth and the like are fine for basic playback but are difficult to work with inside a DAW. There are hundreds of free and paid synth plug-ins designed for use in DAWs. There are quite a few free synths mentioned here.

Check the CC value sent by the pedal in MIDI-Ox. This will tell you what CbB is receiving from the pedal.

It is true, Guitar Rig and Amplitube are audio FXs. They may be used with anything that makes a sound including the output of soft synths. They may be added to audio/instrument track FX racks, Prochannels and audio clip FX racks. They may not be added to the FX rack in MIDI tracks and clips. Only MFX plug-ins like these may be added to MIDI FX racks.

A bad idea that should have generated a warning when running CbB. ASIO4All is not recommended under any circumstances especially when a device has a manufacturer supplied ASIO driver such as Focusrite. Generic ASIO drivers are known to conflict with real ASIO drivers. Uninstall ASIO4All and install the Focusrite driver. CbB could not find a MIDI input device in Windows. Please provide information about the hardware, OS and model of Focusrite interface.

Please provide information about the hardware, OS and images of Preferences > Audio > Devices Preferences > Audio > Driver Settings Preferences > Audio > Playback and Recording and if this is about MIDI data also include images of Preferences > MIDI > Devices Preferences > MIDI > Playback and Recording

Please do not cross post.

Try changing the file extension from webm to mp4 before importing

When KORG added resizable UI to collection 1, it was only available through KORG Software Pass. That is why I started using it. It may have changed since then IDK, I purchased collection 3 since then.

Don't need to see the problem, the 2/3rds of the requested audio preference images are enough to suggest a solution. Try setting UseHardwareSamplePosition to False in Preferences > Audio > Configuration File AFAIK all Digidesign interfaces need this change.