Promidi

Exactly what automation is preset in the destination track and what parameter is it controlling?. You state that "although I have done some automation in the clip I'm adding the pasted one to, there are nodes at the end, ending any automation." Even if the automation ends before where you paste the clip, your track still still be in whatever state the automation is controlling before the pasted clip. Say the automation is controlling volume, and the automation ends with the volume at say 50%, that is what the volume will be when your pasted clip starts. You will have to add an automation node the raise the volume at the point where you have pasted the clip.

Before doing the actual paste, check the destination MIDI track for any CC events that could be affecting volume that might be present before where you intend pasting the clip. Most synths and VSTi plugins use CC7 or CC11 to control volume so look for these to start with. The PRV in single controller mode would be the best way to check this.

When the install stalls, are there any files in the following folder? %appdata%\bandlab-assistant\Downloads. If so what are they, and what are their sizes.

I would not order anything from them just yet until all of your recent orders show up on your account page. Nothing beyond 2018 shows up when I know they should be. A lot of the products appear to be old as well. Also, the "specials" are dated Friday, November 23, 2018 7:10:00 PM EST Even though there is browsable data on their website, I do not deem them recovered at this time.

That will means that you'll have to change the buffer size using the configuration software that came with your audio interface. How you do that depends on your particular audio interface.

Note: Requires FULL VERSION of Kontakt 5.8 or above.

Can you give us more information? Version of Cakewalk (numerically, don't just say "the latest")? Version and build number of Windows? What driver mode are you using (ASIO is preferred)? What is your buffer size (preferences | Audio | Driver settings) Are you using any linear phase effects (Therefore uses look-ahead)? Can you switch off all effects (FX in the Mix module) to see if the delay disappears?

Is the Realtek your only audio device?

Can you give us more information. Version of Cakewalk (numerically, don't just say "the latest")? Version and build number of Windows? What driver mode are you using (ASIO is preferred)? What is your buffer size (preferences | Audio | Driver settings) Are you using any linear phase effects (Therefore uses look-ahead)? Can you switch off all effects (FX in the Mix module) to see of the latency disappears?

Preferences > Project > Record : Under recording mode, select "Sound on Sound". Make sure your pitch bend wheel on your MIDI controller is actually transmitting Wheel events.

Also, if you are using SSD drives , you might want to consider disabling prefetch and superfetch......

Note: Requires Kontakt FULL 5.6.8 or above. Will NOT work on the free Player.

You might want to post this in the features and ideas forum https://discuss.cakewalk.com/index.php?/forum/8-feedback-loop/

You might want to start a new thread. However, be prepared to be told that in this day and age, 4gb is not really enough and that you should consider upgrading your ram.

Cakewalk by Bandlab definitely includes Event List view. My first thought is that you are using a workspace (Check top right of Cakewalk's window) that has the event list disabled. Set workspaces to "none" and see if this makes event list visible.

Set Workspaces to "none"

Move you NOW pointer to where you want the project to stop. Then In the event list view, insert an MCI command "stop" there Now, the project will stop at that point where the "stop" command has been placed (regardless of any events following the "stop" command). See: https://www.cakewalk.com/Documentation?product=Cakewalk&language=3&help=NewFeatures.33.html (search for "Automatically stop/pause playback with MCI MIDI events")

It depends on the range of your pitch bend. I use pitch bend generated notes all the time in my MIDI files. I have written a Studioware panel has two sliders. One sets the pitch bend range (using RPN Events) and that other that allows me to set the interval. The Studioware panel calculates the actual correct pitch bend value from the values of the two sliders. It's all based on a value between -8192 to 8181 (The actual pitch bend MIDI event values). The actual value depend on the pitch bend range and the note you want to bend to (or from). The formula is 8191 * (required bend / pitch bend range) Say your pitch bend range is 5 semitones but you have an instance where you want the bend to go up just 2 semitones. The pitch bend value would be 8191*(2/5) When I am entering glides with pitch bend using the PRV, I turn on snap - but use PRV snap over-ride at a resolution of 64th note (sometimes 128th). Any more than that (by turning snap off) can overwhelm some older synths with MIDI data and might drop some.

Title says it all. Website's been inaccessible for days now..

I think you have to consider a random intermittent hardware fault at this stage (or at least rule it out ). CbB is likely using your hardware in a way that makes the fault manifest in a way that SONAR X3e Producer x64 does not. If it really was a Cakewalk issue, then there would be many, many more posts on here reporting the same issue. As I have said, my PC with CbB (see signature for specs) does not experience the crashes you describe. I even use the same bit depth/samplerate/buffer size as you do. Check your Windows event logs for any disk errors (or any hardware errors). What does CrystalDisk info (or equivalent) say as to the health of your disks. It could even be a memory issue. Maybe reseat your Ram and/or perform a memory test. Just confirming that you are not overclocking your PC. Also check your are your system temperatures. From what you're describing, my instincts are telling me random hardware fault at this stage.

I am not experiencing this with the latest Cakewalk 2020.5 Build 039 with Windows 10 1909 loading various VSTis (BBC SO Discovery VST3 being one of them) What have you tried so far. We are going to need more information about your system Looks to be a local issue with your PC What is your OS version. Is your Windows fully patched and your Vdist runtimes up to date (Remember, Windows update does not update Vdist runtimes) The latest 2019 runtimes is 14.27.29016 - available here: https://support.microsoft.com/en-au/help/2977003/the-latest-supported-visual-c-downloads What audio interface? Do you have the latest drivers for all hardware (Check with manufacturer's website, not Windows update) What sample rate and bit depth? What is your Sample buffer size. What driver mode (ASIO being preferred) are you using? Have you checked your event logs for any disk errors (like bad blocks)?

ASIO would be the preferred mode. What have you tried so far? Track Levels, bus levels Are you seeing meter activity on the bus and tracks.. Are the volumes turned up on the actual Audiobox USB? Does the Audiobox USB work with other software? Are you using the latest drivers for the Audiobox USB https://www.presonus.com/products/AudioBox-USB/downloads

No there isn't.

As a test, downloaded the BA exe and reinstalled. This went smoothly on my PC.... so it's got to be a local issue there on your PC. What OS and version do you have ? Have you tried temporarily disabling all antivirus programs (Including Windows Defender) prior to installing BA. I had Malwarebytes Premium enabled during my successful install This should not be required, but maybe run the installer as administrator. Is there an entry in "Programs and Features" for an older version of Bandlab Assistant?. If so, try uninstalling that from there first. Start + Run appwiz.cpl

What happens if you try from this direct link? https://www.bandlab.com/download/assistant/windows