David Baay

? I frequently double-check myself before posting.

See TransDetectorModel= in AUD.INI (Preferences > Audio > Configuration File > Edit Config File).

Actually sends are post-fader by default; you have to go out of your way to make them pre-fader. But, the OP was talking about fading the clip which is pre-everything; when the clip fade hits -Inf, nothing will be sent/output anywhere. But a long enough reverb tail would still be audible. I'm not sure why Kevin's screenshots aren't showing that. A reverb with a 20-sec decay time should definitely be audible as well as visible in the preview waveform at the high vertical zoom level in the screenshot. Here's Sonitus with a 20-second decay after a single metronome click with no zooming:

Hmmm... now I'm confused. LOL In my case, it's the 'adjust tool' techique that creates new nodes. Ctrl+drag moves the existing nodes, resulting in linear transitions to the previous and next nodes on either side of the segment rather than the jumps you're after. ?

If the goal is see the signal on CbB's Master bus as stated, Input Echo is necessary. If the goal is just to hear the input, then, yes, direct monitoring will do the trick.

The OP used the term 'send' but was really just having and issue with the track output. In all my years, I have almost never had a a problem with signal routing that didn't ultimately turn out to be my mistake and fixable without replacing anything.

Sync problems can have many causes - often user-error/misunderstanding as bdickens suggested. Start a new thread and share a copy of the clip/project.

Sticky-selected = track number is highighted. This is old terminology that may no longer appear in the Ref. Guide, but the functionality is unchanged for ages. EDIT: looks like I was mistaken that the time ruler selection wasn't happening in both cases. But it disapears on releasing the left-click after making the move if you don't have the track pre-selected so I hadn't initially noticed it happening while making the move. In any case, I can only reproduce a problem when selecting in the timeline as Mark described so its not clear to me that he's fixed your specific issue.

That's why Outrage Productions suggested, "Check the folder preferences for project templates, then look in that folder using file explorer for the actual <project>.cwt files." Correcting the path or restoring the template files to the specified path from a backup should fix it. I can't say I've ever seen an update cause a probem like this, but I have all my folder paths pointing to custom locations that are not touched by installs/updates. If I know of some new content being added that I want to use, I copy it over to my custom locations. But I just checked the default Content path, and the default template files are there as expected.

This is working as expected in the latest release for me. The time ruler selection only happens if the track is sticky-selected rather than just focused. But either way works as described in the parent track without having to open the automation lane. I don't know why it's not working in your original video clip. Can your reproduce it in a new, basic project?

Your screenshot shows the track is armed to record so the meter is showing a live input signal, but Input Echo is not engaged so that input is not being ouput to the Master bus. Rebooting alone would not have fixed that.

The problem with more frequent releases is that problems are more frequently attributed to updates when they're just garden-variety configuration/usage issues. A lot of level issues with exported files can be attributed to exporting the wrong source. One common case is exporting 'Entire Mix' when you have a send to a headphone output or other secondary monitoring output on your interface resulting in duplication of part or all of the mix in the rendered file. Another is having the level of the hardware/driver bus set to something other than 0dB and exporting Main Outs or Entire Mix. To avoid problems like this, I always recommend exporting just the Master Bus. The level of the exported file will always match the output level shown in the Master Bus meter - no ifs, ands or buts.

Start a new thread for your particular case. There are dozens of different possible causes of crackles. Your symptoms sound like your DPC Latency is spiking. https://www.resplendence.com/latencymon Run this tool at the same time as Cakewalk. and see what it shows. Common causes are Bluetooth and WiFi drivers; one or both may need to be disabled in BIOS to stop this.

Buying on JRRShop with code GROUP will get you another 20% off. https://www.jrrshop.com/pianoteq

Buy used/open box.

Enable Snap 'By' instead of Snap 'To' at measure resolution, and Ctrl+drag the selection instead of copy-paste (add Shift to constrain movement to one dimension - time or pitch, whichever is detected first.)

Here's the thread for that specific theme:

What keyboard? Does it not have a vendor-supplied driver? I've never had a physical MIDI device that didn't have a dedicated driver so wouldn't ever have seen this.

Welcome to the forum. Kind of an odd problem to have, but will try to help. - What sound source (hardware synth module/keyboard or soft synth), and what keyboard controller model? - USB MIDI direct from the controller, or 5-pin DIN connections to a MIDI interface? - At what point does it stop working, and is it just on playback or also while rehearsing/recording? - Does it happen in a new project? - Check the Event List view or Controller pane in the Piano Roll View to verify sustain on/off controller events are present where expected.

Hmmm... that's a new one on me. Some typical things to check/try: - Are you using MME driver mode (MIDI > Playback and Recording, not Audio), - Any chance the keyboard was moved to a different USB port at some point? - Is it in a USB2 port? - Ar the ports assigned as a Control Ssurface when not intended? - Any onboard MIDI devices or other oddness shown in Device Manager? - Disable anti-virus. or exclude driver paths. - Rename TTSSEQ.INI and have CbB build a new one.

Are the keyboard MIDI ports enabled in Preferences > MIDI > Devices? Is it working if the keyboard is powered up before CbB is launched?

No, it's not normal for this to not be working. It's working as usual with my MIDI interface in the current release. That said, I have occasionally seen auto-detection fail to display the pop-up, but I'm inclined to lay the blame on Windows not signaling the driver load properly.

Going back to this earlier statement and the related screenshot, I'm gathering you recorded a mono input to a stereo track to begin with. This isn't causing the problem per se but it complicates the understanding of how FX will behave. Ideally you should first bounce that track to Split Mono with no FX active, delete the empty right-channel track, and start over with the remaining mono clip on a mono track with FX moved to that track.

What FX are on the Master, and are there any Sends on the track in question to other buses? Clearly some FX downstream of the track is adding right-channel information. It looks like an exact copy of the left channel which suggests maybe the FX is mono-only so the same signal gets sent to both ouput channels of the bus. You'd have to hard-pan that bus to get the desired result. It might help to understand what the ultimate goal is. Are you exporting stems to be mixed and mastered in another program/environment? Normally you would have everything routed to some intermediate bus and export those buses, bypassing any FX on the Master. But you'll still have the issue of mono-only FX producing a centered output.

If possible, share a project/MIDI file (even just one track with a full-length clip that is not truncating as intended), letting us know exactly where you're trying to end it. EDIT: Missed that bouncing to clips resolved it.