SirWillyDS12

No not recording on the keyboard, recording in Cakewalk... I know what you're trying to do, I do it with my Kronos... What I was saying was add "One" note to every track you use on the Pa900 and save the setup to a Standard Midi File... That small file will contain the Patches you used with just one note on every track... Basically saving the Song Setup to import into Cakewalk with the Patches you used...

If Your Korg Pa900 is like my Kronos it will save all your Patches to a Standard Midi File... You can save your song setup on the Pa900 to a Standard Midi File... Open the midi file with Cakewalk and it will contain all the Patch Changes and the channel information... You would have to be in Sequencer Mode and have a least one note on every track you use before you save the Standard Midi File on the Pa900... You could then put those Patch changes into your midi file in Cakewalk... Then when you save it and import it back to the Korg it would contain the proper Patches...

And if you turn on "Write Automation" while doing that Cakewalk will remember it and play it back like that if you have "Read Automation" on...

Ok Russ, So I looked at your screen shots again a little closer... It appears that you have your Driver Mode set to WASAPI Shared... You need to set it to ASIO in Preferences... That is why you can't set the ASIO buffer... Preferences -> Audio - Playback and Recording Under Preferences -> Audio - Driver Settings you should see "ASIO Panel" and not "Wave Profiler"... And I agree with Byron, you need to uninstall the generic Asio Drivers...

In general the clip or note you are editing will be highlighted... If no other notes or clips are "highlighted" you are editing only those notes\clips... You always have the "undo" command when editing notes... And save your work often and there is also the auto save feature you can turn on... There is a feature called "Linked Clips" that will apply the edits to all Clips that are linked... Linked clips are highlighted with a boarder around them... I always "color code" all my linked clips... Cakewalk has a lot to offer if you want to take the time to learn how to use it... I've used FL Studio in the past, and have even used it as a plugin inside of Cakewalk... It has some nice features but doesn't come close to Cakewalk, IMHO...

You can start with... Working with MIDI clips MIDI Groove Clips Matrix view Arranger tracks

Yes...

"Cakewalk" has been fully 64 bit compatible since Sonar 5 in 2005... So if your "older" program is Sonar 5 or after you can simple install the 64 bit version on your machine... Anything older than Sonar 5 you could probably install the 32 bit version and use the 32 bit VST's with bitbridge as Promidi stated... You may also be able to use the 32 bit DX effects but it involves using a DX to VST wrapper... Not Recommended... This is a spread sheet that someone compiled that tells you what plugins came with what version of Sonar... Sonar Plugins 3 to X3 You maybe be able to cross reference and look for the plugins you are looking for and if they are available in another version of Cakewalk that you may have...

The "Buffer" setting is higher in the one setup that you uploaded screen shots for... And the Asio driver is reporting a Latency of 10ms... So you're getting what you ask for... Try reducing the buffer size...

To follow up with Byron... What are your Driver Settings, Sample Rate, Buffer Size? Midi Driver playback buffer settings?

And what if you want different Automation on the Linked Clips? I use linked clips on different tracks and use different automation envelopes on them...

Are you triggering the SI Electric Piano with your mouse on the little VST keyboard? If so you will not Record Midi to the midi track... There will be no Midi Events at the input to the Midi Track, only Midi Events input to the VST... So there will be nothing for Cakewalk to Record... Audio will output from the VST to the Audio Track that will record...

Very possible that you can either disable the Pitch Wheel or set it to "Zero" on your controller... If you actually use the Pitch Wheel then that would be a problem... You can also set Cakewalk to not respond to Pitch Wheel control changes in Preferences -> MIDI -> Playback and Record... It will not respond to or record pitch control changes... You can also install Midi View to see just how much info your controller is sending to Cakewalk... Midi View doesn't show every thing but does show Pitch Wheel controller... You may also be able in install something like MIDI Patchbay to filter out the control changes into Cakewalk if you can't fix the Pitch Wheel...

Ah 1, Ah 2, Aah 3... Pretty sure you can do this on a per project basis under Preferences -> Project -> Metronome... Project - Metronome If you would like the same setting for every new Project create a Project Template...

That question would be better directed to Novation Support...

That's great, glad it's working out for you... Not sure of your exact setup but one thing to keep in mind is that with Wasapi Shared you will experience higher Latency than what you can achieve with Asio drivers... Very probable that the "crackle" sounds that you were experiencing were from buffer overflows with your Asio driver... A buffer size to small will cause this... With Asio, in general, the smaller the buffer the less the Latency... If Wasapi Shared is working out for you and the latency is not a problem, great... You can always try your Asio driver and adjust the buffer size and see if you can get better latency results... When I am recording with live inputs I set my Asio for very low latency... If I'm mixing a project I will set my buffer sizes to the maximum, high latency...

Check the midi event list for your tracks for Pitch Wheel controller changes... If you are using a Midi Keyboard Controller perhaps the Pitch Wheel on it is sending a control change... Possibly the Pitch Wheel controller is stuck?

Kevin made a very good point here... I use MidiQuest VST with my keyboards and I have to disable the midi input to route them to MidiQuest... (Forbidden Windows driver sharing...) Then use a third party midi loop back driver to interface with Cakewalk... So if Cakewalk would always enable all midi devices that would be a nightmare... But I 100% agree that Cakewalk should remember disconnected devices and not re-assign the next available driver when a device is not present... This can also be a real pain when I open a project without one of my keyboards on...

Are you using a Magic Microphone?

You might want to read and try Freeze tracks and synths from the Manuel...

Fairly sure you are referring to the Browser which by default is docked on the right side, you can dock it else where if you chose... Are your plugins showing up in the FX Rack? If so try to arrange them by a different "Sort by"... The browser view should also change to the new "Sort by"... Perhaps this will bring them back... Did you try reading the Manuel?

I concur with Mark... Word Clock would only be synchronizing you audio devices and not your project Transport... You would still need to use MIDI Sync or MTC\SMPTE to sync your project Transport... SMPTE was developed for use with Motion Pictures and is Tempo independent... They would record (Strip) the Time Code into the film to synchronize the audio and audio equipment with the film... Regardless of who was scoring the sound track for the film they would all be using the same time code to synchronize the audio to the film... If you change the tempo in your project or even have tempo changes during your song in the project the SMPTE\MTC clock stays the same, it does not follow your tempo... If you are using SMPTE to sync you are also sending other info with it, such as frame position... The SMPTE clock is dependent on the frame rate you chose... MIDI Sync, which you can use with your Motu Ultralite will be highly more accurate... It sends out the MIDI clock rate of your project... If you double the Tempo you double the clock rate and accuracy of your projects... If you have tempo changes your clock will follow the tempo change...

Totally Agree... Glad you got it figured out...

You can try MIDIView... It does not display all midi events/messages but maybe what you're looking for... MidiView

If you are using SMTPE as the clock source and every thing is set up right you only need to hit start on the "Master"... The slave, if it is Cakewalk will start as soon as it receives the time code, but it depends on the settings in the Preference --> Audio --> Sync and Caching page... .. With SMTPE you can have some offset in your "sync" between master and slave... I have found syncing with Midi Sync works better and easier... With Midi Sync you need to hit play first on the slave to "arm" it or it will not follow/start... With MIDI Sync and transmitting Song Position Pointer the two projects will stay in time... With SMTPE, from my experience, if you start and stop playback they will drift apart every time you stop... I have "Synced" CbB and Sonar Platinum on the same pc using loopMIDI as the Midi interface... Using SMPTE you also need to check these... Preferences --> Project --> MIDI --> Send MIDI Time Code --> MTC Output Ports --> Your MIDI device Kind of overlooked that in the other post...