Jesse Jost Posted July 23, 2019 Author Posted July 23, 2019 @Blogospherianman thanks for taking the time to write up these issues! We'll investigate in subsequent development cycles. But we also want to be sure that nothing in your report was introduced as a side effect of work done for this release. Are you seeing anything in your list that is new as of 2019.07?
Kevin Walsh Posted July 23, 2019 Posted July 23, 2019 Not sure if anyone else is seeing this. I'm deep into a session and I've just noticed that with smart tool selected and grid snap on and set to whole note, all my clips do not snap to the measure boundaries. I've not seen this before but it's entirely possible that this is expected behavior for some reason after some sequence of steps that I cannot remember taking. This build is on the whole much more stable, even with my Focusrite Solo 2nd Gen interface (not terribly impressed with the USB drivers for this interface.)
Jonathan Sasor Posted July 23, 2019 Posted July 23, 2019 1 minute ago, Kevin Walsh said: Not sure if anyone else is seeing this. I'm deep into a session and I've just noticed that with smart tool selected and grid snap on and set to whole note, all my clips do not snap to the measure boundaries. I've not seen this before but it's entirely possible that this is expected behavior for some reason after some sequence of steps that I cannot remember taking. This build is on the whole much more stable, even with my Focusrite Solo 2nd Gen interface (not terribly impressed with the USB drivers for this interface.) Make sure your snap module is set to "snap to" instead of "snap by". Also check if you have landmarks enabled.
Kevin Walsh Posted July 23, 2019 Posted July 23, 2019 Well, you beat me to it. Somehow the setting reset to "snap by", thanks for jumping on that! I always have that set to "to" and it's been that way for so long that I've quite forgotten about it. I have to look up landmarks, not sure what that one is. I appreciate it!
SteveC Posted July 23, 2019 Posted July 23, 2019 Loving the new Smart Tool options! It's so much easier to fly around when arranging without needing to specifically hit on the upper/lower halves of clips. And that's just the beginning... 1
Jeremy Jensen Posted July 24, 2019 Posted July 24, 2019 On 7/19/2019 at 4:26 PM, Jesse Jost said: Configure the Smart Tool to optionally turn off comping features while editing audio on lanes and re-enable it when you are ready to start building a comp track I'm LOVING this change!
Keni Posted July 24, 2019 Posted July 24, 2019 As with all the fixes, Thanks for fixing the VVocal issue. It appears to be fine now.
fitzj Posted July 25, 2019 Posted July 25, 2019 The file is only 18.574 MB. Is that correct for the fixes listed? 1
Jesse Jost Posted July 25, 2019 Author Posted July 25, 2019 2 minutes ago, fitzj said: The file is only 18.574 MB. Is that correct for the fixes listed? I guess that many fixes ought to weigh about a gigabyte but it's just an update installer, so it's really slim. Thanks for trying it out!
Noel Borthwick Posted July 25, 2019 Posted July 25, 2019 We can give you a bigger file if you prefer - we'll just pad it with silence ? 3
Jesse Jost Posted July 25, 2019 Author Posted July 25, 2019 Bug have mass don't they? With any luck, the installer will get smaller and smaller... 3
fitzj Posted July 25, 2019 Posted July 25, 2019 Thanks, Cakewalk, great work in fixing so many problems. Keep up the good work. 1
Francois van der Merwe Posted July 26, 2019 Posted July 26, 2019 You guys are awesome. Many thanks for the evolution of this great DAW and many thanks for all the testers.
Recommended Posts