Misha

Gswitz, you do not have to do that. I think I have an idea how you want to route this. That was my fundamental mistake, when I started this thread.... In most probable scenario, the software limiter will react to something post A/D conversion. Meaning, if clipping occurs before conversion it is still "game over" and software limiter would not save the day. I think in what I want, only outboard will accomplish...or built in DSP in interface, which unfortunately I do not have.

Gswitz... Maybe I am going crazy... Please see attached. This is while recording... Input meter is active Sonitus is dead (while recording!) If I press stop->rewind->play Sonitus will compress on playback, but not at the time when recording is actually happening.... Are you saying it is possible... to use software limiter while you recording live audio?

bitflipper, Thank you for responding. I guess most of us use some kind of "caveman" approaches. This was one universal approach that Greg / you suggested: "recording quiet and loud parts separately". I have one more that I can share. I have two tuned mics and what I tried is placing one mic 2-3 feet from another, so when clipping occurred on the closest mic, the one further away was more forgiving...."Caveman ate some sugar" approach. Ohhh, no no. This is my baby, not giving up my children. I do have 58 from years back but the tone does not compare for vocals to the one I have on the stick. Room is not the greatest for recording, but more than ok for my needs. Bottom line, there is always room for improving, techniques, treatment but what I am after is trying to reduce minor clipping before it is recorded to Cakewalk when I sing quiet and loud parts in one take. So the question still remains: If outboard compressor/limiter will help to eliminate some clipping before it hits PC. -------------------- Gswitz, You are talking about post recording. I am interested in live scenario. Limiting/compressing "While" you sing...

Martsave, No I did not. I mentioned that it is a large diaphragm and it is a mic of choice. I do not want this thread to wind way off from topic It is not the mic or setup or gain level. It is me who is singing stuff too soft and too loud in same tune in the small room, which results in occasional clipping. All I want to know is if a compressor/limiter will help to address some of clipping. Thanks.

martsave, I will look, but the project is on my backup drive somewhere, I do not have it on PC. slartabartfast, I did not miss your point, I was just teasing. Thank you for taking the time on this. It was a nice read! I get the points you are trying to make loud and clear. My in-laws are professional, (the non pop) musicians, so I know exactly how much guts it takes to have a perfect control of your performance, so the music is balanced. To be truthful, I know that my mixes are total disaster and my tunes are half baked. I am not aiming at public, this is just for me, friends and a very random listeners. I enjoy just writing stuff in a sketch form. As soon as I grasp the general idea of the tune and record a sketch, that is totally fine for my purposes. That is true, but not specifically relating to specifics of vocals. At times I would want close up, sort of gentle presence and harsher vocals in same track. I usually succeed in recording how I want it, but it requires a lot of experimenting and re-takes, a lot of them to be discarded because of clipping. Again, this is not a huge problem at all. I know that compressors are not a magic bullet by all means, but at least I would like to know from somebody who knows if it could help me reduce minor clipping. And if so, which one I should aim for? The compressor or limiter/compressor combo, tube or diod... I am on a budget, but do not mind used gear and rather get something better used than shrink wrapped but of less of a quality. Thank you.

Craig, true. Sometimes I jump a few feet away from mic and then right back to it, just to get the phrasing the way I want I am not a pro (or semi-pro) musician by all means, just a hobbyist doing music thing between work & family choirs. Once I compose/record a tune, I rarely go back to re-sing it or re-mix it. I like the process of creating new material more than production. Since it is open discussion, may I share tune I cooked in spring, that gave me very hard time (and oh boy, did it made me dance around the mic to avoid clipping! )? Maybe somebody kind enough could suggest if hardware compressor or/and limiter would help me in similar scenario with clipping issues, before I buy one. There used to be a shop to rent gear close by, but unfortunately it closed, otherwise I would just rent the thing and try it. Here is the link: https://www.bandlab.com/bluebeat13/tongue-my-foe-57637b27 Thank you in advance, Misha.

slartabartfast, Lol! I am that ignoramus, that likes to experiment with different vocal ranges in one song for the sake of musical expression and just have some stupid fun! I believe that is still legal Yes, sure I will lose some dynamics at very peaks using compressor, but it is better than having some clipping ..in my case. Yes, I tried software that magically "heals" clipping, but I do not like the result of that. My clipping issue is not that serious., around 5-10 seconds total in a single tune (If I would of left it as is, without re-recording sometimes with maaaaany takes) . When I record vocals, it is semi-improvised process, and it seems to me (and I am sure some people here know exactly what I mean) that occasionally the best sections are the ones screwed up with clipping. Then, when I start at fresh takes, I usually lose the drive needed to recreate same thing, and the end result is not as hot as intended. So instead of creative process I get choreographed stage dance thing. P.S. I use a decent, sensitive, large diaphragm mic, and that is a mic of choice.

Marled, bingo! That is what I am battling with I looked at some DBX stuff. Prices are very reasonable. The thing is, I am not worried about "beautification" of sound by getting something that cost as much as used car, but something that would do the job clean, without audible artifacts. I do not want to kill the tone of the nice mic that I am using, just so the compressor kicks in when needed to suppress clipping. P.S. Grant, thank you for reply. V.Rider is a nice little plugin, but it is used on post recording, not in live recording.

John, I am not sorry for the post . I am sorry it is in the wrong place/thread in the forum I know Cakewalk community is awesome. I learned about many cool things about music making from the folks here. M.

Thank you for commenting. Sure, I use various techniques, including multi takes on quieter / louder parts, good pop filter, position of mic, stepping away. Yes, it does help in most cases, but I still think that outboard compressor should solve most of remaining issues.

Thank you for replies! "The caveman approach" LOL! I like that! Actually I sometimes do just that, but as you said, me too thinks it is a caveman approach. That is why I am trying to find a more intelligent way to deal with it. Seems that outboard compressor / limiter is the way to go. My audio interface has FX Inserts, so that should not be a hard task to connect a Limiter/compressor to the chain, before it hits A/D. I was looking at vintage TL Audio Ivory series 5021 tube compressor, which is 10-18 years young. and priced relatively reasonably. The only thing it does not precisely says it is a limiter, but I think it should do what I am after. I am sorry, now I feel that this thread should be outside Cakewalk topics, for some strange reason, I thought that I could use software limiter to limit live input.

martsave martin s, Thank you for trying! Roland "capture" line is solid, I had Duo Capture some years back, but also it was pretty "quiet" unit, it was actually hard for me to make it clip mettelus, I have Arturia Audiofuse. It does not have onboard DSP. Mic positioning, pop filters, shields, stepping away from mic etc.. sure these things work for me to extent. Here is the issue. Some of my tunes have both gentle and aggressive vocals. Lowering the input on interface helps of course, but after using gain in Cakewalk at later stages, brings out room noise and presence is somewhat lost. The last time I used hardware limiter/compressor was 20 years back. I had a beat up, cheap unit from fleamarket. If I remember correctly, It did what it was intended to do, but the quality for "recording" was less than acceptable. Just want to find a solution of taming natural loudness as it comes, without lowering input below comfort level

Byron, Thanks. I guess I am out of luck. I have read Cakewalk thread from years back... I thought things have changed. I guess if I want the workflow I am after, outboard is the only choice. My interface was supposed to have DSP on board, but sadly, that was a Sweetwater misprint. The problem is, I am afraid that average outboard stuff will color and introduce noise to the sound... Probably big bucks outboard limiter/compressors modules will not do that, but I can not afford them

Gswitz., thanks, however this does not answer my question on using a limiter in live scenario, while singing.

Hi Folks. Can anybody tell me how I can use a software limiter in Cakewalk in live scenario to reduce clipping while recording vocals (not after the recording)? Thank you!

Scook, Silly me, I was trying to go directly from synth splitting it to specific buses. Of course that did not work, but when I assigned plugin audio channels to different audio outputs, created audio tracks linking them to these plugin outputs and routing them into specific buses it did work perfectly. Two problems solved. You are helpful and correct as always. Thank you!

Scook, It worked perfectly, no issues with solo button. Thank you!!! Can I please bug you with one other question? I am assuming that if I decide to move a couple of MIDI tracks from same group to different buses, I would still have to create multiple instances of Halion, or there is a more intelligent way to do it? Thank you for your time.

I am ashamed to admit how little I know, and that I am a little lost... What does this mean: "When using multiple MIDI tracks to the same plug-in, it is best to avoid using an instrument track. Split the instrument track." How can I split it without loading multiple instances? Halion Sonic is a single plugin synth that has a multichannel "save" for my midi file that has 5 or more tracks. The only workaround I found is using multiple instances of Halion and routing specific midi tracks to specific Halion instance to specific bus. Please be patient with me P.S. Maybe I am being somewhat unclear. I create my multitrack midi file arrangement and corresponding Halion "multibank save state" outside of Cakewalk. Then, when I am in Cakewalk I create an instrument track (Halion) and use "import midi" to bring in my midi file (which has 5 or more tracks).

Scook, thank you for the reply. Halion is similar to Kontakt...Sampletank in a way. Usually I have my Multi instrument bank saved there. I do not believe opening multiple instances of Halion is wise for the purpose of solving solo button annoyance.

Hi Folks. Probably something ridiculous, just can't find the cure. Here is the scenario. 1) I create an Instrument track in Cakewalk (Halion VST). 2) I import my Midi arrangement (several tracks) to Cakewalk 3) Everything plays as it should... BUT If I solo a single track out of lets say 5 playing (In Cakewalk, not the Halion interface) it will solo that track and the solo is also automatically pressed on Halion instrument track in Cakewalk. If I un-click the solo on the midi track, the solo button on Halion (Instrument track) will remain active, so I have to unclick it manually. Is there a way to fix this, so the solo button is synced to unclick from actual Instrument? I hope I am making sense Thank you!

Hi Folks. One of the most annoying things for me in digital audio recording is audio latency. Especially when recording vocals. I am aware that there are a million reasons why this can happen and even more "tips@tricks" out there, trying to address the issue. So here is my request for the feature. A built in analyzer in Cakewalk, that would run tests on audio input/output of the audio card, system etc on the active setup, meaning with particular opened project or a "heavy" test dummy project....And which would recommend realistic steps, sorted by priority of particular items (Cakewalk or System) that can be addressed on that specific computer to reduce latency, yet preserve the project in original form (no bouncing of tracks, disabling FX etc.) Not "general" ideas as in latencymon, something more particular to the "current" setup/project in Cakewalk. I would call it CALA (Cakewalk Audio Latency Analyzer) I know, this is request is probably too far from reality, just thoughts.

Maybe it is there, I just didn't find it. I am learning something new all the time in Cakewalk, but would love to have a feature of hiding/un-hiding muted take lanes and whole muted tracks, so work space is more manageable. Maybe not a big thing for most of users, but it surely will help some. Thank you for considering!

Bob, thank you for extensive post and trying to help! To clear misunderstanding. I have very powerful computer (for my needs) , that I recorded my projects with. It handled everything absolutely great before recent Windows and Lenovo updates, which came almost simultaneously. After these updates, same projects that were flying under heavy load begun to experience severe problems. With help of folks (posts above), I got it under control. It has to do with power management mostly... I am afraid it is power management firmware that I am up against and not your average software that is possible to "unroll". Lenovo has a tendency of issuing half baked drivers and firmware. Hopefully their gurus correct on next update. You have some really important points written out. Especially about "look ahead" VSTs... and other items such as mixing/tracking buffers, etc. Which I knew, but you put in a compact, easy to read/understand form, which I am sure will be picked up by current and future users. I do have (actually 2) Asio interfaces, which I tried before posting this cry out

mettelus, Thanks! yes, one of the first 10 things I tried to fix this was "un-parked" CPU Turning off network discovery helped a lot. P.S. I am not tech guru, so forgive me if I sound silly, but I think it would be a very useful feature if Bandlab develops a built diagnostic tool that would pinpoint exact hardware / software tensions and clashes that particularly effect Cakewalk stability and would offer suggestion to remedy these.