Jump to content

External Audio Editor


Eric Solomon

Recommended Posts

22 hours ago, scook said:

Quite a while ago (pre X Series) there was a discovery process as part of the installer which added certain editors to the Tools section of the the Utilities menu.

The hooks were retained in the program so the registry entries still work.

I wrote the Tools Editor to simplify the process and remove the need to directly edit the registry.

 

I used 8.5 until CBB came out so I wasn't imagining it then. It used to give me the option of Wavelab that I also had installed.

I think I tried it once and never used it again so no loss

Link to comment
Share on other sites

  • 1 month later...
  • 2 weeks later...
  • 2 months later...
  • 2 weeks later...
On 6/27/2019 at 3:06 PM, scook said:

It is possible today. I wrote a utility called Tools Editor to make it easier to add any program including audio editors (and almost anything else including pdf and html documents) to the tools section of the CbB utility menu. It is available on my google page. Help is built into the program and there is a readme pdf with illustrations including the setup for adding a version of SoundForge.

Once added to the tools menu, to edit a clip, select a clip and launch the audio editor from the menu.

Not sure if Audacity will work as an audio editor though. For a program to work, it must be able to take a wav file as a command line argument. That is how CbB (and many other DAWs) send files to external editors. There are quite a few free and paid editors that do take wav files on their command line.

1. The handoff is for the entire file.  If you only use 5 seconds out of a 50 second audio file, Cakewalk will hand over the entire file to i.e. Sound Forge or RX when you use the Tools menu.  I ran into this issue when I wanted to remove an artifact while editing a Podcast for someone in Cakewalk.  I had to switch to Samplitude and do the work there, because Cakewalk was handing over the entire 1 hour Audio File to iZotope RX.  It was incredibly impractical. 

2. They need to build the configuration for External Editors into the UI.

3. Using Audacity as an Audio Editor from Cakewalk is like using Cakewalk as an  Audio Editor from Samplitude.    It's designed to be used primarily as a non-destructive multi-track recording/editing solution, like Adobe Audition's Multi-Track workspace.  It's a DAW, not an Audio Editor (or Destructive Wave Editor, to be more precise).  If Cakewalk didn't support Virtual Instruments (like Audition), it would be directly comparable to Audacity.  The issue with this is that  when you go to save the file, Audacity defaults to wanting to save a project/session file, so it becomes a bit fugly to use because of all of the extra clicks and directory browsing to get it to overwrite the correct file before going back to Cakewalk.  With Destructive Audio Editors, you press <Ctrl-S> + <Alt-F4> and off you go.  The workflow is considerably smoother, and there is less button mashing/mouse clicking involved.

Link to comment
Share on other sites

47 minutes ago, scook said:

It operates at the clip level. There is nothing to prevent splitting smaller clips out if a larger one and passing that between programs.

That is not what I experienced.  Entire clip was sent to the RX Audio Editor.  In that case, a 1 hour podcast recording, instead of just the 2 second clip that I had split out of it (splitting around the area that I needed to work on).

Link to comment
Share on other sites

13 hours ago, Maestro said:

That is not what I experienced.  Entire clip was sent to the RX Audio Editor.  In that case, a 1 hour podcast recording, instead of just the 2 second clip that I had split out of it (splitting around the area that I needed to work on).

This is correct. If you want to only send a small portion, you need to bounce that clip first. 

Here's the rub, if you have to denoise the clip, it's a lot easier to denoise the entire hour long podcast first and then snip and bounce if you want to make additional adjustments. That way it doesn't send the hour clip to RX. I do this non-stop with mixing DX. 

Link to comment
Share on other sites

On 9/24/2020 at 6:10 PM, Josh Wolfer said:

This is correct. If you want to only send a small portion, you need to bounce that clip first. 

Here's the rub, if you have to denoise the clip, it's a lot easier to denoise the entire hour long podcast first and then snip and bounce if you want to make additional adjustments. That way it doesn't send the hour clip to RX. I do this non-stop with mixing DX. 

 
 

I didn't need to denoise a clip.  I need to use the Spectral Editor to remove a noise from the people upstairs doing work while we were recording ?

If I needed a DeNoise, I'd have just used the RX  De-Noise Plugin, instead...

In other DAWs, the DAW just knows how to send only that clip to the Audio Editor.  It does a "bounce in place" automatically and then replaces that clip with the edited clip when you're done.

Edited by Maestro
Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...