Jump to content

Inter-track distortion recording dual mono in CbB


Xibolba

Recommended Posts

I'm getting distortion when I record (for example) interface channels 1 and 2 as dual mono tracks in CbB.  I do not get this distortion using Reaper or Studio One.  I have found it true with any pair of interface channels seen to CbB as a stereo pair.   Quick example:

In CbB the first to channels of my interface may be addressed as:

  • input 1 left mono
  • input 1 right mono
  • input 1 stereo

If I record two microphones into interface channels 1 and 2 into a CbB stereo track as input 1 stereo I don't get distortion.  

If I record two microphones into interface channels 1 and 2 into a pair of CbB tracks using the sources input1 left and input1 right respectively I do get distortion.

 I'm really hoping it's a trick I'm missing, hence the post.


The test:
This experiment demonstrates the distortion artifacts found when recording low frequency signals in 
adjacent tracks within a stereo pair (by this I mean one microphone in left input 1 and the other in 
right input 1).

An interesting note is that adjacent channels outside  a stereo pair (e.g.: input 1 right and input 3 left) do not have the distortion artifact.

Description of the test bed:
  The source is a upright bass playing pizz (sloppily) through a 2 octave chromatic scale
  The interface is a Focusrite Clarett 8Pre X (Thunderbolt)
  Two SM57 microphones on a stereo bar positioned 12" in front of the source
  One microphone is labled A and the other B
  Microphones are connected to inputs described in scenarios  
  Microphone preamp gain set to 12 o'clock on channels under test
  No parameters changed between tests except as noted in the table below
  Recorded at 96/24
  Exported at 96/24 no dithering
  
General observations;
  No meter registered above -26 dB, (interface, focusrite control, DAW) while recording or during playback

  The quality of the distortion is akin to an extreme EQ boost with a narrow Q where you can hear the filter ringing at resonance.

  The distortion is present in both tracks - it is not an artifact of playing both tracks simultaneously.

  Outside that directly demonstrated by this test, level doesn't seem to change whether or not distortion is present.

  I have reproduced this problem recording amplified electric bass and also drum kit with strong low frequency components (e.g: low toms and bass drum, low power chords on guitar) with a variety of microphones (SM57, RE-20, K-2, SM25, R10, ...).

  In all observed cases the source recorded on both channels was the same (as in the case of this audio example) or similar (as in the case of low toms and bass drum where this is always bleed).

Audio examples:

             Channel
Test      Mic A  Mic B  Result
--------- -----  -----  --------------------
One         1      2    distortion
Two         1      3    no distortion
Three       7      8    distortion
Four        6      8    no distortion
Five        2      3    no distortion


DAWS involved in testing:
   Reaper
   Studio One
   Cakewalk

Hardware involved in testing:
   multiple Presonus interfaces (from FireStudio to StudioLive 16.4.2)
   multiple Focusrite interfaces (from Scarlett/USB to Clarett/Thunderbolt)


The audio is too large to drop here - a link to the writeup, a picture of the recording setup, and a CbB project that demonstrates the audio artifacts may be found here: 

https://drive.google.com/drive/folders/10J5yQVtnrTSXbQws7KwNAfjCttG_5FFm?usp=sharing

Thanks for any info.

Microphone setup.jpg

Link to comment
Share on other sites

Did you look at pan laws p.207 in manual?

What you do with mono tracks after - sum to a bus as is centered, panned full left right etc makes a difference.

Difference daws have different pan laws, some can be selected - not so in studioone(you have to use a stock plugin for that).

In Reaper and Cakewalk you can select what to use.

Link to comment
Share on other sites

2 hours ago, Xibolba said:

No meter registered above -26 dB,

 

3 minutes ago, LarsF said:

What you do with mono tracks after - sum to a bus as is centered, panned full left right etc makes a difference

Unless he boosted the resulting clips to at least -3, I doubt pan laws are the issue. 

I could be wrong.

Link to comment
Share on other sites

I played back the tracks as is - I didn't want to introduce any extraneous processing in the example.  I kept the tracks centered and besides playing both back, I soloed each.  The two tracks are summed to a master buss.  No plugins present.  The distortion artifacts are present in the tracks and not affected by panning.  While this example is setup to demonstrate the distortion artifacts, what I'd normally do is place the mics to pickup different aspects of the sound and then mix the mono tracks together.

I can work around the issue by recording in stereo and then either splitting the track to two mono tracks or send each channel to a different aux track.  Should that really be necessary?  Seems like recording dual mono in adjacent tracks should not result in distortion.

I think I said it in the writeup, but it's not recording two mono tracks that results in distortion, it's only when the two mono tracks are recognised by CbB as elements of a stereo pair.

Am I missing some trick or setting?  Is it a bug?  It's really apparent in the project I shared (link in original post).  I could record at lower bit/sample rates and drop .mp3's here, but as this is an audio fidelity issue it seems better present the best possible wav files.

From outside the box it feels as if different code paths are executed here and one of them isn't behaving well.  Or I'm missing a trick ...

Link to comment
Share on other sites

Today I've been recording a bass guitar through adjacent mono inputs (1+2, 3+4,  etc.)  to two mono tracks. I can't duplicate the OP's problem. However this...

1 hour ago, Xibolba said:

it's only when the two mono tracks are recognised by CbB as elements of a stereo pair.

confuses me. I have an Orion 32+. CbB displays all of it's inputs as Left, Right or Stereo just as OP described here.

 

17 hours ago, Xibolba said:

In CbB the first to channels of my interface may be addressed as:

  • input 1 left mono
  • input 1 right mono
  • input 1 stereo

There is not another setting as far as I know.  Select a stereo input to record to record a stereo track. Select a mono input to record a mono track.  That's it.

I wish I could be more helpful but I have no idea why you are getting that distortion. All I can do is confirm that it works properly for me. 

Link to comment
Share on other sites

On 6/14/2020 at 11:46 AM, Base 57 said:

Today I've been recording a bass guitar through adjacent mono inputs (1+2, 3+4,  etc.)  to two mono tracks. I can't duplicate the OP's problem. However this...

confuses me. I have an Orion 32+. CbB displays all of it's inputs as Left, Right or Stereo just as OP described here.

 

There is not another setting as far as I know.  Select a stereo input to record to record a stereo track. Select a mono input to record a mono track.  That's it.

I wish I could be more helpful but I have no idea why you are getting that distortion. All I can do is confirm that it works properly for me. 

Thanks for that feedback - especially that you were recording bass frequencies.  It's been a while I've been avoiding the dual mono scenario since being bitten.  It's worth another go.

Link to comment
Share on other sites

On 6/14/2020 at 3:17 AM, Xibolba said:

I'm getting distortion when I record (for example) interface channels 1 and 2 as dual mono tracks in CbB.  I do not get this distortion using Reaper or Studio One.  I have found it true with any pair of interface channels seen to CbB as a stereo pair. 

Be sure that Remove DC Offset During Record
in Cakewalk Preferences -> Audio -> Playback and Recording
is unchecked.

 

Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...