Nuno.P

41 minutes ago, Craig Anderton said:

What you may find is that for some reason, most VST3 sims can't accept program change commands, even if the VST2 versions can. I've tested quite a few plug-ins and had consistent results. I'm not sure why, there's no technical reason why it shouldn't be possible.

One more thing. Did you tested only with cakewalk or also with another DAW software?

31 minutes ago, Craig Anderton said:

What you may find is that for some reason, most VST3 sims can't accept program change commands, even if the VST2 versions can. I've tested quite a few plug-ins and had consistent results. I'm not sure why, there's no technical reason why it shouldn't be possible.

Thanks Craig, That´s it.

YOu replied wen i was also writing. As i was also testing it took me a long time writing it.

Anyway i guess i should contact Bias about it and hope they can fix it!

Thanks very much for your Help scook!

You are correct in everything, but my problem persists. I now know a litle bit more about it!

Iam using a footswitch that has program changes, bank changes and two buttons with cc

With Bias VST2 patch and bank changes work. I also can assign my two CC footswitches to whatever i want.

With Bias VST3 patch and bank changes don´t work. The 2 cc Switches works well. The same happen with TH3.

So as i was trying to send midi pressing the patch change footswitches i though midi was not reaching the Plugin.

I don´t know if it´s a cakewalk or bias problem. But TH3 also don´t recognizes patch and bank change buttons.

But looking further, Bias VST2 changes patches and banks but don´t allows me to assign one of those buttons to any other funcion with midi learning. Only the two cc buttons work with midi learn.

So it may be a bias problem.

i don´t know if anyone can help me more in such a specific problem. I guess i will contact PositiveGride

Hi, 

While using Bias FX2 with cakewalk i was trying to send midi information to the plugin. It works well on Bias Standalone.

Made all the correct configurations but it didn´t work. After a while i tried it with the VST2 version of Bias and it worked well. Went back to VST3 version and nothing again.

So my doubt was if it was a cakewalk or a Bias problem. 

So i also tried with TH3 VST3 and it didn´t worked. So i guess is a cakewalk problem.

Anyone of you was able to send Midi to a VST3 plugin?

Note:

And yes, i done the right configuration: Configure plugin as Synth. Activate midi in. Created midi track and sent midi to Bias VST3 and later to TH3.

I didn´t worked.

I even recorded midi to make sure the problem was not in my midi device. Only worked with VS2 version of Bias.

Great as i already ordered the SSL2+!

2 hours ago, Morris Band said:

Oh and everything  sounds a bit different through it on headphones. 

Hi, strange.

no better or worst? just different?

Thanks for helping.

it´s always hard to make a choice. Looks like there are great options around. 

Hi Bapu, 

Babyface current version is RME Babyface Pro FS and it´s way more expensive rhan SSL 2+

I guess SSL 2 will give me a huge improve over M-audio C600 and M-Audio Projetmix. 

Sometimes i need more imputs but i guess i can live with just two!

I do prefer at this moment better quality with less imputs. But i need two headphones output and Midi.

I guess SSL 2 only lacks ADAT.

I wonder if they are working in a more complete model.

Hi,

My M-audio C600 is dying and i need a new interface.

Any one uses Solid State Logic SSL 2 and 2+ with Cakewalk?

2 Imputs are enough for me as long as the pre amp is good as the convertors.

ADAT would be great but i can live without it!

Great.

Removing the E shorcut is a small great thing. I disable fx so many times by mistake.

well after all the problem was all inside my two pcs.

After reset the aud file the problem was gone

well i found the problem.

I was using the sonitus compressor in a fx bin inside Prochannel. 

If i move it out to the normal fx bin it works well.

So the bug is just inside prochannel....

Can anyone load to project and check in their system?

it´s a small project just for testing.

onedrive link

https://1drv.ms/u/s!AnURB6w23tA6iclCOKALayNoSe0_rA?e=xcEegu

Hi,

iam having trouble using sidechain with sonitus compressor and gate.

I have a lot of pops and Drops. If i start with the sends on i will have a drop. I can enble them one by one while play is on.

Did anyone had this problem before?

Have this in two different pcs.

Here is a link to a bundle where this happens.

Can anyone help?

https://1drv.ms/u/s!AnURB6w23tA6iclCOKALayNoSe0_rA?e=xcEegu

(Sends are disable in track 3. YOu need to enable them to test?

thanks for all your interest and coments.

User 905133, track presets are a great way to improve your workflow and save time.

Bus presets are not as important as track presets but can also save you time when you use FX Bus, or Parallele Compression Bus, One of the most important FX Bus is the Reverb Bus. Instead of starting always from scracth you can have a few presets you fine tune over time to start as a base.

it´s not a huge deal. It´s just a very simple way tosave time and be more efficient.

The workaround is:

create a audio track

Insert sends to the reverb bus you want.

Save a templete of that audio track.

Then insert that audio track in another project and it will also creat the required bus.

I just think its 's easy to do this directly inserting bus from template

It would bew great if bandlab adds the CA-2A to cakewalk.

I love the prochannel

i want to insert the bus in a existing project. Not a new one.

If yu do that in the tracks you can "insert from a template"

In the Bus section you haven't got that option

Hi,

Great Work bandlab team.

What about bus templates?

It probably is easy to do it.

WIth track templates and project templates you can insert bus but not directly.

I use reverb Bus as a lot of people and diferente templates for diferent reverb bus would be great.

amazing