Noel Borthwick

It's not the default because the old behavior did not automatically cut out data after the stop playback point. With the new option, if the new recording is longer than the existing clip, then the underlying clip could be removed. This could be unexpected for some some since it didn't do that before...

If you have been logged out of your BL account for months, then Cakewalk cannot auto activate when needed. If you stay logged in, you won't have this issue. Once in a while the token expires so you have to log in again but its not very often.

To clarify - Is it slower only when the option is enabled?

That’s not accurate. Cakewalk adds that folder by default to the scan path.

What dropout code are you getting in the message when it drops out. That should indicate the cause.

If you attach the dump file that is created (link is shown in error dialog) it ma help us find what’s causing it.

How are your MIDI tracks routed? Are you playing them through a virtual instrument VST? If so the sounds would always be synchronized with audio playback as long as you are hearing audio tracks correctly because they are delay compensated. Make sure that you are not using the Microsoft MIDI synth device. Safe mode may have worked for you since it switched the driver mode to WASAPI (windows audio)

I was referring to inserting tracks not the rme device

I have the fireface and it takes less than a second to insert a single track. No difference whether the device is on or off though. If you turn off the audio engine does it insert quickly?

Adding tracks is instantaneous. If you are you using a control surface disable it and test again. Also what audio interface and driver mode are you using? Certain drivers are known to bog down the system so use a process of elimination to find out what’s causing the issue.

Did you actually get a crash dialog which shows the dump file location? If not it was not detected as a crash.

I didn't supply the instructions to clean uninstall the app I doubt that was required to solve this issue. But yes there should be a caveat that doing that will remove any plugins installed to the VstPlugins folder.

I think there is an actual bug here however. If I move the mouse over the left of a track and scroll, and then immediately move the the effects bin it scrolls the view properly. However if I wait a couple of seconds with the mouse over the effects bin it wont scroll anymore. Will look into it and see. why that happens. Edit: its actually not a bug. in CbB we support scrolling the FX rack unlike Platinum. So its attempting to scroll the rack instead of the tracks view. You can verify by adding plugins to the rack. We'll see if its feasible to improve the behavior in the future.

Have you tried starting Cakewalk without your audio interface plugged in? PS please change the title of your post since we have isolated that it is unrelated to 2022.02 Also, another couple of things to try: Start cakewalk and repersonalize by holding down CTRL when clicking the Cakewalk icon. Respond to the prompt and allow it to re-personalize. Check if this resolves the issue. If that doesn't work add the line below under the WinCake section in Cakewalk.ini that is found under %appdata%\Cakewalk\Cakewalk Core. Then try starting the app. If it crashes send us the dump file. [WinCake] ExceptionHandlingSeverity=7

If you look in task manager do you see a cakewalk.exe process after the splash screen disappears? Usually issues like this mean something is causing the main process to terminate. Try and backtrack to any changes you might have made earlier since you mentioned that it was working earlier.

You can easily verify if it's specific by rolling back to the prior release and retesting. If it's a problem that appeared days after updating chances are it's unrelated.

This thread is for feedback specifically about the 02 release. If you have a general issue and need assistance post it on a different thread.

Right as you guessed we have a timer to prevent inadvertently changing control values. People complained about accidentally changing values while meaning to scroll so this delay was added to alleviate such issues. I don’t remember if scroll wheel works on the effects rack but it it is treated no differently from other track or mixer controls.

The error message you list is not ours but from the Microsoft installer from the redist itself. This link seems to indicate that your windows installers may need repair. https://thegeekpage.com/the-feature-you-are-trying-to-use-in-on-a-network-resource-that-is-unavailable-in-windows-10-fix/ Also read this. https://answers.microsoft.com/en-us/protect/forum/all/the-feature-you-are-trying-to-use-is-in-a-network/80d4be22-aab6-47f0-a7dc-8a3131fc8df0?page=2 It seems that a registry entry on your pc may be pointing to a non existent drive which may be confusing the Microsoft installer. Check the path that it lists in the error message and follow those links.

@Twaddle did you follow this procedure and still have no success? BTW your post isn't about running Cakewalk. It's that you can't run the installer...

Sends are treated similarly to outputs. So if a bus is deleted, any sends to it are assigned to “none” rather than being deleted. Its probably there to allow the user to reassign it later otherwise you would lose settings and send automation. Also to facilitate undoable bus deletion so multiple reasons.

Well, its a plugin crash what help do you need? You posted the text file not the dump file.

The global FX button also bypasses prochannel fx.

We install all redists that are REQUIRED by Cakewalk so using the installer provided should address any Cakewalk related issues.

Not all companies can keep up with the latest versions that is normal. However waves does test with Cakewalk and report issues to us. Changes on incremental releases are very unlikely to affect global compatibility.